
Reference: 8430095616954
Brand: Nazza
Nazza Isopropyl Alcohol
Isopropyl alcohol, also known as 2-propanol or isopropanol, is used as a cleaner for electrical contacts. -Does not le
Reference: 8430095616954
Brand: Nazza
Isopropyl alcohol, also known as 2-propanol or isopropanol, is used as a cleaner for electrical contacts. -Does not le
Reference: 572-1205
Nozzles (nozzle) for 3D printer, valid for most printers and materials on the market. See in the description the opti
Reference: CAPPTFETL
Brand: Capricorn
This item is sold in units of 10 cm, you can adjust the desired length, adding as many units as you want. We will supply the tube to you continuously for lengths less than 2 m. (for example if you add 5 units we will send you a continuous tube of 50 cm) High quality Teflon tube, with very low friction and high temperature resistance. Capricorn XS vs TL...
Reference: REF000081R
This item is sold in 10cm units, you can adjust the desired length, adding as many units as you want. We will supply you with the tube continuously for lengths less than 2m. (for example, if you add 5 units we will send you a continuous tube of 50cm) Generic Teflon Tube Inner Diameter (ID): 1.9mm ± 0.15mm Outer Diameter (OD): 4.0mm
Reference: 8411322235803
Brand: 3dlac
3DLAC SPRAY 400ml - STRONG AND LONG-LASTING ADHESION - EXTENDED DURABILITY (APPROX. 400 APPLICATIONS) - NO WARPING Its function is to maintain the first layer of plastic to maintain the start of printing constantly, avoiding undesirable errors. 3DLAC is the perfect replacement for Kapton tape and otros types of fasteners due to its cost savings and easy...
Banner
heatbreak / Barrel to attach to the Block and heatsink of your hotend, select the right type and model.
*All metal: the input Teflon only reaches the top of the barrel, the rest of the route is done through the metal interior of the barrel, prevents the inlet Teflon from touching the nozzle making it suitable for high temperatures at which Teflon can degrade. However, this type of barrel It requires a few degrees more temperature and is usually more prone to clogging.
*Bore 4.1: The input Teflon reaches the other end by touching the nozzle. In this type of barrel It is essential that the Teflon is of quality if it is going to be printed at more than 230 degrees, as well as that the cut of the Teflon is completely perpendicular to avoid gaps between it and the nozzle. Make sure when inserting the Teflon that it reaches the nozzle to avoid gaps between the two.
Model compatible with hotend Volcano.
Valid for Artillery X1/Genius with threaded extruder cap.
Material: Steel
Bottom Diameter: Threaded M6
Top Diameter: Threaded M7
Length: 22.5mm
Non-original article E3D
Reference: CAPPTFETL
Brand: Capricorn
This item is sold in units of 10 cm, you can adjust the desired length, adding as many units as you want. We will supply the tube to you continuously for lengths less than 2 m. (for example if you add 5 units we will send you a continuous tube of 50 cm) High quality Teflon tube, with very low friction and high temperature resistance. Capricorn XS vs TL...
Reference: CUVOLPT100
Silicone cover for the MK8, MK9 and MK10 extruder hotend. Not compatible with e3D or compatible extruder hotend. A silicone cover guarantees the protection of the hotend as well as providing a more stable printing temperature during the first few layers, by protecting it from the air generated by the layer fan once it bounces off the printing bed. The...
Reference: REF000606
Precision needle kit for the proper cleaning and maintenance of your printer nozzle. Always use with a hot nozzle Each kit contains 10 needles
Reference: ARTD017
Brand: Artillery 3D
Size:40X40X10mm Voltage: 24V Cable Length: 75mm Connector: 2PIN-XH2.54 Compatibility: Artillery X1, Genius, X2, Genius PRO
Reference: ARTD012
Brand: Artillery 3D
Original heater for the hotend of your Artillery X1 or Artillery Genius.24V, 64W, VH3.96 Terminal
Reference: ARTD013
Brand: Artillery 3D
Temperature Sensor (Thermistor) original for Artillery X1/Genius/x2/Genius Pro Connector-XH2.54, length 80mm, head diameter 3mm Photo shown for illustrative purposes, product may not correspond exactly as Artillery It supplies sensors that, while they are all compatible, are not aesthetically the same.
Reference: REF000644
Teflon tube cutter with sturdy ABS body. Suitable for cutting flexible plastic tubes. Cutting with this tool ensures that the tube is not crushed during cutting, as well as a perpendicular cut, which will avoid jamming problems. WARNING: The color supplied may not match the one shown in the photo
Reference: REF000081R
This item is sold in 10cm units, you can adjust the desired length, adding as many units as you want. We will supply you with the tube continuously for lengths less than 2m. (for example, if you add 5 units we will send you a continuous tube of 50cm) Generic Teflon Tube Inner Diameter (ID): 1.9mm ± 0.15mm Outer Diameter (OD): 4.0mm
Reference: 6834892538792
Heatbreak or barrel high-quality "all metal" type in which the Teflon inlet only reaches the top of thebarrel, the rest of the route is carried out through the metal interior of the barrel, prevents the input Teflon from touching the nozzle so it is suitable for high temperatures at which Teflon can degrade. This type of barrel It may require a few...
Reference: ARTJ024
Compatible Aluminum Block E3D Volcano, requires nozzle Volcano What's not included thermistor, heater or heatbreak/barrel. Includes hardware Valid for Artillery Genius, X1, Genius PRO, X2
Reference: 572-1205
Nozzles (nozzle) for 3D printer, valid for most printers and materials on the market. See in the description the opti
Reference: REF000544AC
Precision-machined nozzles with a sharp tip. Some models have the size coding by dots on the head, being the coding 3 points: 0.4mm 4 points: 0.6mm 5 points: 0.8mm 0 points: 1mm * Price per unit
heatbreak / Barrel to attach to the Block and heatsink of your hotend, select the right type and model.
*All metal: the input Teflon only reaches the top of the barrel, the rest of the route is done through the metal interior of the barrel, prevents the inlet Teflon from touching the nozzle making it suitable for high temperatures at which Teflon can degrade. However, this type of barrel It requires a few degrees more temperature and is usually more prone to clogging.
*Bore 4.1: The input Teflon reaches the other end by touching the nozzle. In this type of barrel It is essential that the Teflon is of quality if it is going to be printed at more than 230 degrees, as well as that the cut of the Teflon is completely perpendicular to avoid gaps between it and the nozzle. Make sure when inserting the Teflon that it reaches the nozzle to avoid gaps between the two.
Model compatible with hotend Volcano.
Valid for Artillery X1/Genius with threaded extruder cap.
Material: Steel
Bottom Diameter: Threaded M6
Top Diameter: Threaded M7
Length: 22.5mm
Non-original article E3D