- Out of stock

Reference: 8430095616954
Brand: Nazza
Isopropyl alcohol, also known as 2-propanol or isopropanol, is used as a cleaner for electrical contacts. -Does not le
Reference: 572-1205
Nozzles (nozzle) for 3D printer, valid for most printers and materials on the market. See in the description the opti
Reference: CAPPTFETL
Brand: Capricorn
This item is sold in units of 10 cm, you can adjust the desired length, adding as many units as you want. We will supply the tube to you continuously for lengths less than 2 m. (for example if you add 5 units we will send you a continuous tube of 50 cm) High quality Teflon tube, with very low friction and high temperature resistance. Capricorn XS vs TL...
Reference: REF000081R
This item is sold in 10cm units, you can adjust the desired length, adding as many units as you want. We will supply you with the tube continuously for lengths less than 2m. (for example, if you add 5 units we will send you a continuous tube of 50cm) Generic Teflon Tube Inner Diameter (ID): 1.9mm ± 0.15mm Outer Diameter (OD): 4.0mm
Reference: 8411322235803
Brand: 3dlac
3DLAC SPRAY 400ml - STRONG AND LONG-LASTING ADHESION - EXTENDED DURABILITY (APPROX. 400 APPLICATIONS) - NO WARPING Its function is to maintain the first layer of plastic to maintain the start of printing constantly, avoiding undesirable errors. 3DLAC is the perfect replacement for Kapton tape and otros types of fasteners due to its cost savings and easy...
Banner
Flexible steel strip coated with smooth PEI and/or textured PEI valid as a printing surface. A strap of this type allows you to easily release the pieces once printed by flexing the strap. The built-in magnetic adhesive sheet makes it easy to separate and attach the strap to the hot bed without the need for clamps or otros
similar methods.The strap can be used on both sides, and each side can be of a different type (smooth/textured) or both the same, select the desired combination
It consists of two parts: magnetic adhesive sheet and flexible strap
The strap can be used on both sides, and each side can be of a different type (smooth/textured) or both the same, select the desired combination
The textured side leaves the printed piece with a slight grainy texture while the smooth side will leave a smooth finish.
Isopropyl alcohol is recommended for cleaning on a frequent basis, and only on occasions when there is a loss of adhesion use acetone or hot water and a degreaser for dishwashers. Continued use of acetone is harmful to
PEI****Attention: Smooth PEI is highly adhesive to PETG or TPU, so it should not be used for these surfaces without a separating agent, we recommend printing these materials on the textured side
****Attention: to avoid damaging the PEI surface, the nozzle must be located at the correct height or higher. If it is too low, it may scratch the PEI or cause excessive adherence of the part
Manufacturer: Makerex
Reference: 8430095616954
Brand: Nazza
Isopropyl alcohol, also known as 2-propanol or isopropanol, is used as a cleaner for electrical contacts. -Does not le
Reference: CAPPTFETL
Brand: Capricorn
This item is sold in units of 10 cm, you can adjust the desired length, adding as many units as you want. We will supply the tube to you continuously for lengths less than 2 m. (for example if you add 5 units we will send you a continuous tube of 50 cm) High quality Teflon tube, with very low friction and high temperature resistance. Capricorn XS vs TL...
Reference: REF000691
Material: Nylon Length: 1 meter Diameter: 6mm, 10mm, 15mm, 20mm. Braided cable. Strong corrosion resistance Color: Black
Reference: 572-1205
Nozzles (nozzle) for 3D printer, valid for most printers and materials on the market. See in the description the opti
Reference: 575-1317
Nozzles (nozzle) for 3D printer, valid for most printers and materials on the market. See in the description the opti
Reference: TTBRTIT
Brand: Makerex
Metal arm for the original extruder of the printers Artillery X1 and Artillery Genius or for any Titan type extruder Incorporates sprocket for better filament traction
Flexible steel strip coated with smooth PEI and/or textured PEI valid as a printing surface. A strap of this type allows you to easily release the pieces once printed by flexing the strap. The built-in magnetic adhesive sheet makes it easy to separate and attach the strap to the hot bed without the need for clamps or otros
similar methods.The strap can be used on both sides, and each side can be of a different type (smooth/textured) or both the same, select the desired combination