Filter By
Categories
Categories
Brand
Brand
Price
Price
€2.00 - €128.00
There are 16 products.
Reference: 1869
Brand: Anet
0 review
2.8 inch screen for ET4/ET4X/ET4 PRO
Reference: MKSSGLV1.0
Brand: Makerbase
0 review
MKS SGEN V1.0 32Bits Motherboard
Reference: 6834890045940
Brand: Makerex
Rear Stabilizer Bar Kit for Artillery 1 x With this kit you will be able to give your printer chassis additional rigidity which will result in a higher quality of your prints, especially in parts with a certain height. *In addition to the assembly of the kit we recommend whenever possible the placement of the filament spool outside the original holder...
Reference: FTL50X50
Brand: Makerex
Flexible steel strip coated with smooth PEI and/or textured PEI valid as a printing surface. A strap of this type allows you to easily release the pieces once printed by flexing the strap. The built-in magnetic adhesive sheet makes it easy to separate and attach the strap to the hot bed without the need for clamps or otros similar methods. The strap can...
Reference: 6834893940846
Brand: Makerex
0 review
Kit for Artillery X1/Genius/X2/Genius Pro: Heater Thermistor
Reference: SEAUTT3P
Brand: TwoTrees
0 review
A touch-type self-calibrating sensor, unlike inductive sensors, can work on any type of printing surface: metal, plastic, glass, etc. Valid for any brand and model of printer that has the appropriate connectors on its motherboard, requires a firmware update for its update Standard on printers such as ANET ET4
Reference: 728
Brand: Anet
0 review
Motherboard Anet ET4 version 1.1 32bits Drivers A4988 Valid for Anet ET4.
Reference: 727
Brand: Anet
Motherboard Anet Version 1.7 Input voltage: 12V-24V Item Size(W x H): approx. 9.7*9.2cm / 3.8*3.6in Valid for Anet A8, A8 plus, A6, etc.
Reference: 722-1648
Brand: TwoTrees
0 review
The surface Ultrabase It is made up of small micropores that once heated provide additional grip to the piece, once cooled the piece loses that additional grip being easier to peel off. With a heated base of this type, the need for additional adhesion methods such as lacquer, glues, etc., is very rare. This type of base is becoming more and more common,...
Reference: 720-1646
Brand: TwoTrees
0 review
Driver TMC2208 ultra-quiet 4-layer. -Version 3.0 with better heat dissipation - Compatible with a4988/drv8825 drivers - Up to 256 microsteps -Srealthchop Mode -SpreadCycle mode via UART
Reference: TTBRTIT
Brand: Makerex
Metal arm for the original extruder of the printers Artillery X1 and Artillery Genius or for any Titan type extruder Incorporates sprocket for better filament traction
Reference: MKDR2209
Brand: Makerbase
0 review
Driver TMC2209 ultra-quiet 4-layer. -Version 3.0 with better heat dissipation - Compatible with a4988/drv8825 drivers -Up to 256 micro-steps -Srealthchop mode -SpreadCycle mode via UART
Reference: ARTD001
Brand: Makerbase
Integrated MKS-GEN L V1.0 controller for 3D printer developed by Makerbase to optimize existing issues on the open-source controller board such as Ramps 1.4. Replacement plate for Artillery X1/Genius/Hornet
Reference: REF000131
Brand: Makerex
0 review
Pack of 5 compatible FEP sheets for Anycubic Photon/Photon-S or any model of resin printer with the same or smaller dimensions of the bucket. Dimensions: 20x14cm
