There are 200 products.
Reference: REF000654A
Measure:50X50X15mm Voltage: 12V/24V Power: 0.1V Bearing type: Sleeve Bearing Cable length: 28cm Connector: 2 Pin
Reference: REF000706
Brand: Anycubic
0 review
NTC 100 K thermistor for Anycubic e3d v5 hotend. Includes metal bushing for attachment to the block.
Reference: REF00070512
Brand: Anycubic
0 review
Heater 40W for hotend Anycubic.
Reference: REF000664
0 review
Temperature Sensor//Thermistor NTC 3950 100k ohms Connector: Two-pin Head: metallic
Reference: REF000665
0 review
Temperature Sensor//Thermistor NTC 3950 100k ohms Connector: No Length: 1M Head: glass
Reference: 437-3722
Brand: Creality
Characteristics: Thermistor NTC pre-wired for most heat bed and extruder 3D printers. Resistance: 100 K ohm sensor. Connector: Terminal 2 P. Durable material for a long service life. Rated Resistance R25 (25 degrees C): 100 k Resistance Accuracy: +1% B-value R25/50: 3950 k Accuracy B: +1% Operating Temperature Range: -40 degrees C~+300 C Power...
Reference: REF000654
Brand: Fysetc
0 review
Measure: 50x50x15 mm Voltage: 5V Amperage: 0.35A Bearing Type: Sleeve Bearing Cable length: 28cm connector: 3 Pin MOLEX 5057-9403 Compatibility: Prusa MK2, MK3-S
Reference: REF000081R
This item is sold in 10cm units, you can adjust the desired length, adding as many units as you want. We will supply you with the tube continuously for lengths less than 2m. (for example, if you add 5 units we will send you a continuous tube of 50cm) Generic Teflon Tube Inner Diameter (ID): 1.9mm ± 0.15mm Outer Diameter (OD): 4.0mm
Reference: ARTD013
Brand: Artillery 3D
Temperature Sensor (Thermistor) original for Artillery X1/Genius/x2/Genius Pro Connector-XH2.54, length 80mm, head diameter 3mm Photo shown for illustrative purposes, product may not correspond exactly as Artillery It supplies sensors that, while they are all compatible, are not aesthetically the same.
Reference: ARTD012
Brand: Artillery 3D
Original heater for the hotend of your Artillery X1 or Artillery Genius.24V, 64W, VH3.96 Terminal
Reference: ARTZ030
Brand: Artillery 3D
24Plastic Arm for Original Replacement Extruder for Printers Artillery X1 and Artillery Genius.
Reference: ARTD018
Brand: Artillery 3D
50Size:40X40X20 100 Voltage: 24V Cable length: 40mm Connector: 2PIN-XH2.54 Model with built-in mouthpiece Compatibility: Artillery X1, X2, Genius, Genius PRO
Reference: ARTD017
Brand: Artillery 3D
Size:40X40X10mm Voltage: 24V Cable Length: 75mm Connector: 2PIN-XH2.54 Compatibility: Artillery X1, Genius, X2, Genius PRO
Reference: REF000629
Brand: Artillery 3D
0 review
Original replacement extruder for printers Artillery X1, X2, Genius and Genius PRO Note: does not include the metal cap where the screw barrel.
Reference: REF000503
0 review
Hotend MK8 with block and nozzle 0.4mm Hole for thermistor type bulb (requires clamping socket) It does not include a heater or thermistor, they can be purchased separately. The item supplied may vary in colors from the one shown
