4020 Artillery X1/X1/X2/Genius/ Genius PRO Turbine Fan

Reference: CAPPTFETL

Brand: Capricorn

Teflón Capricorn Premium XS

8 reviews

This item is sold in units of 10 cm, you can adjust the desired length, adding as many units as you want. We will supply the tube to you continuously for lengths less than 2 m. (for example if you add 5 units we will send you a continuous tube of 50 cm) High quality Teflon tube, with very low friction and high temperature resistance. Capricorn XS vs TL...

Reference: REF000111

Kit 10 Cleaning bits

0 review

kit of 10 drill bits for cleaning and eliminating nozzle jams. Preheat the nozzle before use. Available in different sizes: 0.4, 0.6, 0.8 and Mix (0.2, 0.3, 0.4, 0.5, 0.6, 0.7, 0.8, 0.9, 1, 1.2).

Reference: REF000606

Nozzle Cleaning Needles (10 units)

6 reviews

Precision needle kit for the proper cleaning and maintenance of your printer nozzle. Always use with a hot nozzle Each kit contains 10 needles

Reference: REF000629

Brand: Artillery 3D

ARTILLERY X1/Genius extruder

0 review

Original replacement extruder for the Artillery X1 and Artillery Genius printers. Note: it does not include the metal cap where the barrel is screwed.

Reference: ARTD017

Brand: Artillery 3D

Hotend 4010 Artillery X1/X1/X2/Genius/ Genius PRO Fan

2 reviews

Measure:40X40X10mm Voltage: 24V Cable length: 75mm Connector: 2PIN-XH2.54 Compatibility: Artillery X1, Genius, X2, Genius PRO

Reference: ARTZ030

Brand: Artillery 3D

ARTILLERY X1/Genius Extruder Arm

1 review

Plastic arm for the original replacement extruder for the Artillery X1 and Artillery Genius printers.

Reference: ARTD054

Brand: Artillery 3D

Artillery X1/Genius optical sensor

2 reviews

Optical final race limit sensor for Artillery X1/Genius. Available combinations: X-Axis Sensor: 5cm. Y Axis Sensor: 60cm Z Axis Sensor: 10cm (For machines without an external connector to the chassis for the Z axis it is necessary to include the article “Artillery Optical Sensor Extender”)

Reference: ARTD012

Brand: Artillery 3D

Artillery X1/Genius Hotend Heater

5 reviews

Original heater for the hotend of your Artillery X1 or Artillery Genius.24V, 64W, VH3.96 Terminal

Reference: ARTD013

Brand: Artillery 3D

Hotend Artillery X1/Genius/X2/Genius Pro Temperature Sensor

7 reviews

Original Temperature Sensor (Thermistor) for Artillery X1/Genius/X2/Genius Pro Connector-xh2.54，length 80mm, head diameter 3mm Photo shown for illustrative purposes, the product may not correspond exactly as Artillery supplies sensors that, although they are all compatible, are not aesthetically the same.

Reference: REF000081R

Teflon tube

5 reviews

Generic Teflon tube Inner diameter (ID): 1.9mm ± 0.15mm Outer diameter (OD): 4.0mm You can adjust the desired length, adding as many 10cm units as you want. We will supply the tube continuously for lengths less than 2m.

Reference: 6834897089350

Cutting Pliers

1 review

Cutting pliers, ideal for cutting filament. *The model supplied may not correspond exactly (color, shape of the handle, etc.) to the one shown in the photo

Reference: ARTJ055

Heatbreak V6 Kraken Steel

7 reviews

*All metal: the inlet teflon only reaches the top of the barrel, the rest of the way is through the metal interior of the barrel, it prevents the inlet teflon from touching the nozzle, making it suitable for high temperatures at which teflon can degrade. However, this type of barrel requires a few degrees higher temperature and is usually more prone to...

Reference: CEALBLA18

18cm Metallic Brush

3 reviews

Don't you know how to clean the hotend of those damn scraps of material? , with a brush with metal bristles you will be able to remove most of the debris that remains on your hotend. Perform the cleaning with the pre-heated hotend It is recommended to turn off the printer or at least not be heating the hotend when using the brush to avoid a possible short...

Reference: ARTJ024

Hotend Volcano Artillery Block

7 reviews

E3D volcano compatible aluminum block, volcano nozzle required Does not include thermistor, heater or heatbreak/barrel. Includes screws Valid for Artillery Genius and X1

Reference: 572-1205

Volcano Nozzle (Steel, brass, etc.)

9 reviews

Nozzles (nozzle) for 3D printer, valid for most printers and materials on the market. See in the description the options to select

Reference: ARAIRDC

Brand: Artillery 3D

Artillery X1/Genius fan nozzle

1 review

Nozzle for layer fan (turbine) Artillery X1/Genius